What did you do to your TRX today?

[Boosted]

How is it attached to the truck?

Bolted to the bumper.

 

[Bambi]

I haven’t bought anything in about a year. I refuse to pay the prices there asking. It’s coming down now but I’ll wait it out. Still have my stash also. Just haven’t shot as much.

Good news is no issues and drove great for having close to max payload. Thats 1100 pounds on the pallet to give an idea of squat

 

[Phillytrx]

I seen it squat, very nice.

 

[Fifty]

Bolted to the bumper.

Ok. So you drilled through the plastic or is there a metal support there? Sorry. Mines on order so I can’t look at a bumper to tell.

 

[Boosted]

Ok. So you drilled through the plastic or is there a metal support there? Sorry. Mines on order so I can’t look at a bumper to tell.

The bumper is metal. 3 holes right through the front, then installed nutserts (rivnuts) and used grade 8 3/8" hardware.

 

[Two]

A "reach stick"?!? I must be driving mine completely wrong.
If there's anything in the bed, it's always jammed up against the tailgate when I get home.

 

[Happypants]

A "reach stick"?!? I must be driving mine completely wrong.
If there's anything in the bed, it's always jammed up against the tailgate when I get home.

I need one of those sticks... my stuff is always jammed up against the tailgate UNTIL i get home and come slidin in (and i dont even have my trx yet)

 

[hellcat07]

@OnTheReel what did you use to fill the bracket holes on the bumper?

3/8" ID Hole Locking Plugs for Panels - Nylon Plastic 0.375 Inch ID Round 9/16" Head Diameter - for Panel Thickness .016" - .125" | Body n Sheet Metal Hole Plug | by SBD (10): Amazon.com: Industrial & Scientific​

3/8" ID Hole Locking Plugs for Panels - Nylon Plastic 0.375 Inch ID Round 9/16" Head Diameter - for Panel Thickness .016" - .125" | Body n Sheet Metal Hole Plug | by SBD (10): Amazon.com: Industrial & Scientific
www.amazon.com

Eastwood Spray Gray Detail Paint Aerosol 12 oz​

Matches original equipment withthe look of freshly cast iron

www.eastwood.com

 

[BDS TRX]

Well folks!!! In today's TRX dreams, I . . .




. . . man, I swear, reading all you guys' posts about tinkering on your TRXs is making the wait even harder!

I, legit, can't wait to be able to post to this thread!!

 

[Ravage]

Got the RAM flag graphics installed!
Not very sticky. Concerned my foam wash system will peel them off. But they look great!

 

[RaptorTillNow]

I got my R7 mounted up high, fuse-tapped into the fuse box...

Tomorrow's project, Retrax PowerPoint MX install

 

[2crazy2stop]

Made the best a little louder

 

[Boosted]

Ok where do i get this?

I'm sure there's other places to get one but I got it through https://bestlicenseplateframes.com

 

[juicebox]

I got my R7 mounted up high, fuse-tapped into the fuse box...

Tomorrow's project, Retrax PowerPoint MX install

That's a nice install! I just did the same with a V1G2, and tapped into the fuse box so I can run a concealed display on my steering column. Pictures to come once I am done, but it was super easy to run the wire along the headliner and down the A-pillar and into the fuse box with a wire tap!

 

[Teghogh]

The bumper is metal. 3 holes right through the front, then installed nutserts (rivnuts) and used grade 8 3/8" hardware.

There goes your “bumper” to “bumper” warranty.

 

[Happypants]

Needs a dab o duct tape somewhere, but custom bumper inbound

 

[EMS-PILOT]

View attachment 15831
Did some vinyl work on the front end to make that RAM pop!

I have the same truck....Im up in Sammamish! We should meet for coffee!

 

[Boosted]

Uh oh….

 

[TReX-RAM]

Uh oh….View attachment 23390

Is that a good uh oh or a bad uh oh??

 

[Boosted]

Is that a good uh oh or a bad uh oh??

Fake news uh oh…. Finally getting the front end aligned after installing the level kit. lol