What did you do to your TRX today?

[LTCBPL]

I got a set of those sill protectors sitting on my desk. Just need to get some nice weather and some motivation to install them. Install pretty straight forward?

Yep, just place them on and mark the middle or the sides with something to make sure you are perfectly centered. Rubbing alcohol the surface and stick it on. I had to redo one because I thought I could eyeball it. I just happen to have plenty of that 3m double tape laying around.

 

[Snowbaruu]

I working with a local fabrication shop in the Bay Area. I can give you the details once the prototype is done if you like. Will be easy for them to replicate once all the measurments and brackets are correct

Molle panel went in today. We went through 10 sets of brackets to get it right. Fits like a glove now. The plastic molding pieces on the left and right need small cut outs to account for the brackets. I used snips and a dremel. Aside from that there is no drilling required. Mounting uses all oem holes. You do need to remove the seats to get it in though.

The fab company I worked with is called MCY Industries. If anyone is interested you can reach out to them on insta:

https://www.instagram.com/mcyindustries?igsh=MzRlODBiNWFlZA==

 

[TRXMIKE]

Molle panel went in today. We went through 10 sets of brackets to get it right. Fits like a glove now. The plastic molding pieces on the left and right need small cut outs to account for the brackets. I used snips and a dremel. Aside from that there is no drilling required. Mounting uses all oem holes. You do need to remove the seats to get it in though.

The fab company I worked with is called MCY Industries. If anyone is interested you can reach out to them on insta:

https://www.instagram.com/mcyindustries?igsh=MzRlODBiNWFlZA==

Good luck crawling in that slider fuckers! This is awesome

 

[Snowbaruu]

Good luck crawling in that slider fuckers! This is awesome

Right! I can only imagine the look on their stupid face haha

 

[RamTrxUSA]

Molle panel went in today. We went through 10 sets of brackets to get it right. Fits like a glove now. The plastic molding pieces on the left and right need small cut outs to account for the brackets. I used snips and a dremel. Aside from that there is no drilling required. Mounting uses all oem holes. You do need to remove the seats to get it in though.

The fab company I worked with is called MCY Industries. If anyone is interested you can reach out to them on insta:

https://www.instagram.com/mcyindustries?igsh=MzRlODBiNWFlZA==

Thank you for sharing I’ll be reaching out to them today. Exactly what I’ve been looking for.

 

[04Ram2500Hemi]

Put these Weathertech door sill protectors. They fit perfect, hard plastic, easy install. I had scratched the shit out of my drivers side, enough for me to get some paint quotes. I came to my senses tho. Glad I went this route. They look good with @BigRays custom inserts.

When I first bought my truck I had clear bra put on all four doors at that spot.

 

[LTCBPL]

When I first bought my truck I had clear bra put on all four doors at that spot.

I thought about that too late

 

[Wyoming_TRX]

Installed an engine block heater for next winter. It was pretty easy.

 

[Landonsrt]

Finally installed the Oracle light bar today and a Redtiger front and rear dash cam from Amazon.
The light bar ended up to be a big hassle because one of the riv nuts decided to strip. I had to drill it out of the bumper and replace it with an expansion sleeve and bolt. Oracle responded with the size i needed. Ace hardware had never heard of a riv nut before.

Now I need to go to five below and buy a 10 ft usbc cable. Don’t want to use the outlet cable it came with.

 

[TRX_SAV]

Full color match and headlight corner reflector blackout

 

[TRX_SAV]

 

[Krewton]

View attachment 142864
View attachment 142865
View attachment 142866

All black color match looks good! Not a fan of other colors colored match but yours is sexy. You have a Borla Atak with those Borla tips? Thought I was going to be a cold start video and got excited

 

[TRX_SAV]

All black color match looks good! Not a fan of other colors colored match but yours is sexy. You have a Borla Atak with those Borla tips? Thought I was going to be a cold start video and got excited

Thanks man, opportunity missed lol, I do have the Atak and just got tips to go with all the color matching.

 

[Blackbear]

Full color match and headlight corner reflector blackout
View attachment 142854

Oh shit! That is exactly what I want to do! Looks awesome, man! Great call.

 

[TRX_SAV]

Oh shit! That is exactly what I want to do! Looks awesome, man! Great call.

 

[Obxtrx]

D1 limbo for me, so this the best I can do right now…View attachment 11956

I

 

[Obxtrx]

I View attachment 142872

The wine is soooo god !

D1 limbo for me, so this the best I can do right now…View attachment 11956

 

[Blackbear]

View attachment 142870

How did they do that? Disassemble the headlight and tinted that reflector?

 

[Blackbear]

Molle panel went in today. We went through 10 sets of brackets to get it right. Fits like a glove now. The plastic molding pieces on the left and right need small cut outs to account for the brackets. I used snips and a dremel. Aside from that there is no drilling required. Mounting uses all oem holes. You do need to remove the seats to get it in though.

The fab company I worked with is called MCY Industries. If anyone is interested you can reach out to them on insta:

https://www.instagram.com/mcyindustries?igsh=MzRlODBiNWFlZA==

Are you doing bulletproof side windows too?

 

[TRXMIKE]

Are you doing bulletproof side windows too?

There are panels you can get for the rear doors. Basically if you wish you can make it a cage back there. Waiting for someone to do so with a trapdoor rear slider, they get in but can't get out!