LORD VADER your truck is now being MODDED! New Pics added as Requested by Peeeeps.

[Humzila]

Apparently the only disavantage is the box doesnt stay open on its own ,.will need a little prop stick or bungee;

 

[Humzila]

Aluminum hard cover with cross rails and rhino xtray basket

 

[TReX-RAM]

Du_ha box underseat

Apparently the only disavantage is the box doesnt stay open on its own ,.will need a little prop stick or bungee;
View attachment 10781

I wonder if you threw some Velcro adhesive strips on the top of the box if it would stay open...?

 

[Humzila]

I wonder if you threw some Velcro adhesive strips on the top of the box if it would stay open...?

View attachment 10797

Good idea - it wouldnt take much - prob have some around to try, thx.
right now i have to figure out why the left side seat wont latch - dont see anything different from the right which latches fine.

 

[Humzila]

Finished some of the projects today:

 

[TReX-RAM]

Finished some of the projects today:

Looking good, the mods flow really well

 

[Caliche]

Finished some of the projects today:

Yeah that looks amazing and very Beastly! Cheers.

 

[Humzila]

Almost done in the bed until i decode how to trim once side wall. Molle panels etc.. are in

 

[Humzila]

Joined the showing off the easter egg crowd - sent the engine cover to storage - looks sooooo much better.

 

[Humzila]

Not sure what these little cutouts were meant for but i found a use - fits new HK Rescue knife perfectly and tight enuf it stays in place, plus misc gear;

 

[Bambi]

The side clearance is giving me serious anxiety. Yikes.

I did an open trailer because I thought the risk of damage on an enclosed trailer was worse than Enviromental damage

 

[Humzila]

I did an open trailer because I thought the risk of damage on an enclosed trailer was worse than Enviromental damage

I can vouch for the specific team from Reliable - literally one inch at a time.

 

[Humzila]

Working on a few new mods .
Headrest hexgrid is Velcro to attach pouches or patches.

the hooks are also standard bottle holders.

 

[Humzila]

Examples of how you can keep adding onto the molle panels- oxygen, tourniquet, life hammer, etc.

 

[Humzila]

This is a quick detach trauma kit not yet filled, but on a Velcro backer attached to the molle- it’s just rip and go.
And then the always present tape measure now secured instead or rumbling around in the door pocket.
On the door is a really good set of jumpers from energizer - 25 feet, 1 gauge in a nice case which will be mounted on the bedside molle.

 

[04Ram2500Hemi]

Apparently the only disavantage is the box doesnt stay open on its own ,.will need a little prop stick or bungee;
View attachment 10781

I‘ve been curious about the rear under seat storage, so I appreciate this picture. I may have to add this to the list when my truck shows up.

 

[Humzila]

I‘ve been curious about the rear under seat storage, so I appreciate this picture. I may have to add this to the list when my truck shows up.

Solved the stay open issue with bungee balls from the latch loop to the seat release when open - only need one side

 

[Humzila]

Superwinch in a box:

 

[humble]

This thread has to much good content with pictures and explanations. Thank you @Humzila !!!

 

[thewrx]

how much was thas tow hook, like $1500!

I have a similar setup with my bed cover, using yakima cross bars w/ a basket like above or 2-4 bike mounts.